Flexispot Standing Desk Evaluation …Flexispot Mb Standing Desk…
Cons: What I Didn’t Like About the Flexispot E7
Though the cons on this desk are very little, here are a couple of features that I wasn’t always a substantial fan of:
The package that the desk came in was heavy, so bringing it inside was a group effort, but this is simply a repercussion of how tough the Flexispot is.
The convenient cable tray was a little bit confusing to install. In the end, you ultimately slip it under screws, which wasn’t very clear from the directions.
You will need to purchase an anti-fatigue mat to stay comfy, however this is a good idea for any standing desks, so I can’t fault Flexispot for that.
When it arrived and I saw how heavy it was, I was both fired up (since this meant it was going to be tough) and likewise a little hesitant (due to the fact that all of us understand how much of a difficulty assembling furniture can be).
The good news is, with the help of an educational YouTube link, it took me just around 42 minutes to put together. Scratch that, it took my 11-year-old child, with some supervision from me, from start to finish. The only hang-up I have with assembly was the cable tray, which I discovered wasn’t described well in the instructions.
When put together, I like the streamlined appearance of this desk. I’m confident any of the many varied finishes that it can be found in would look terrific in any workplace, and the adjustable width makes it easy to fit it in even the smallest of office.
The peaceful operation and height memory settings make it easy, efficient, and peaceful to change in between sitting and standing as sometimes as you desire throughout the day.
This desk is sturdy. It can hold up to 335 pounds even while in operation, so if you have a substantial home computer (or want to take a nap on it for some reason) it has you covered. It will likewise uniformly distribute weight no matter how out of balance the weight you put on it is, it won’t wobble or wiggle.
in that video is quite kitted out as the desk we’re looking at today is pretty standard I attempted to get as near that as I might on uplifts website with comparable setups the flexi spot desk we’re looking at today will run you about four hundred and ten dollars versus 6 hundred and fifty for a similar desk from uplift I attempt to get as close as possible with the uplift model is actually five inches longer however you can do a lot with five inches boom yes now for transparency flexi area did send this desk out for evaluation but as you must know by now does not impact my review in any way the desktop here is 55 inches broad 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming but it’s not delivering till completion of April at the earliest the desktop is an inch thick but it’s this standard laminate as you can perhaps get lacking even any cable television grommets for travel through the outside container
for the desktop was not damaged in any way which is utterly bizarre because I could shoot a 30-second b-roll montage of simply the damage and defects on this desktop scuffed scraped pitted simply extremely rough man if I had actually acquired this I ‘d have been on the phone with customer support right away they did also managed to miss drilling the pilot holes where you can attach the control box to the desktop a lot of having to do that myself without unintentionally drilling through the other side of the desktop so yeah pilot holes in wood screws is how you’re gon na be connecting the surface area to the frame that’s a far cry from the ingrained metal inserts that we saw on the uplift desk so assembly aside from having to drill that top was in fact pretty uncomplicated the entire thing came together in about 45 minutes and despite the fact that there’s cables running to it from each component to support motorized function strangely definitely where any kind of cable television management materials whatsoever the frame on this unit is a single motor double phase style versus the double motor three-stage design that comes requirement with the uplift desk this can be upgraded too to both the dual phase double motor and a three-stage double motor which pushes the expense of the desk up
an extra 70 bucks the frame is created for a max load of 154 pounds and it moves at a rate at an inch per 2nd the height can range from simply under 28 inches to simply over forty 7 point six inches so a max I ‘d it is more than tall enough even for me and I stay at 6 foot for this design does come basic with the control panel that enables up-and-down movement plus three memory spots with an LED readout to tell you the desk height the single motor style uses this drive shaft assembly which needs to be changed as the width of the desk is changed the motor operation itself while it might be slow is extremely quiet as in barely audible this outside a cost would be the one advantage I would provide this system over the uplift desk and I want to beware here because this isn’t a hit piece this desk is 240 dollars cheaper than the comparable uplift model over 35% cheaper even if you upgrade this flexi area test to the dual motor three-stage design it still comes in a hundred and seventy dollars more affordable than the uplift but more affordable doesn’t imply inexpensive this desk is still over four hundred dollars if I had paid over $400 for this desk I ‘d have a problem with that the front to back stability of this desk is strong even if max height I’ll absolutely offer it that but the lateral stability of this desk the horizontal motion at this price point it’s undesirable it’s add fuel to the fire here they consist of a little safety baffle this little steel piece that installs to the frame and covers a portion of this rotating driveshaft when
this desk sees any lateral movement at all the drive shaft hits this baffle and the sound is definitely infuriating to top things off I decided to add rolling casters to this desk this was a $30 upgrade and two of those 4 casters arrived damaged also my plan for this desk at this point is to lose the desk top and featured completely and replace it with a white laminate lemon table from Ikea and use it as an adjustable picture table which you can’t do this frame will accommodate desktops approximately 63 inches wide and 31 and a half inches deep so this will roll around the studio make it easier to film items without having to adjust complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I found uplift initially that is an investment in quality workplace furnishings that will last you this at best feels like a less expensive imitation of that it just does not feel quality and the difference between this desk and my primary desk is night and day do do not hesitate to take a look at their website as well which likewise feels eerily similar to one of their competitors there’s a wealth of devices you can get for the flexi spot desk as much as and including a foot massager and even a fixed exercise bike and I might invest another 10 minutes of our valuable time covering different options and devices I might but I believe I’m happier that they only sent out a basic desk since as a standard desk I’m not a fan of the quality control at this cost point and I do not think slapping on a lot of additionals is the relocation when the core product isn’t what it need to be they do provide a 30-day trial if you’re just morbidly curious and they warranty their desks for 3 years really desk is 5 years and uplift desk is seven years if you are Flexispot Mb Standing Desk
in the market for a sit-stand desk they’re incredible mine’s been a life changer for me both in terms of video gaming and efficiency but I would spend the extra money it’s gon na require to enter a higher end maker like uplift desk or extremely desk and I have not personally utilized really desk items so I can’t speak on it however their track record is very good big thanks to flexi spot for sending this out for review regrettably I can not recommend this unit and for the record I’m a hundred percent sure they would have gladly changed the parts that I had an issue with viewing as how both the desktop and the casters showed up damaged but from a consumer perspective you ‘d probably be really delighted to get this in